| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix tid_tx use-after-free on BA session stop
ieee80211_stop_tx_ba_cb() hands tid_tx to kfree_rcu() through
ieee80211_remove_tid_tx(), and then reads tid_tx->ndp after dropping
sta->lock:
ieee80211_remove_tid_tx(sta, tid); /* kfree_rcu(tid_tx, rcu_head) */
...
spin_unlock_bh(&sta->lock);
if (start_txq)
ieee80211_agg_start_txq(sta, tid, false);
if (send_delba)
ieee80211_send_delba(..., tid_tx->ndp);
That read is not covered by an RCU read-side critical section, and it runs
in preemptible process context: both callers hold the wiphy mutex, reaching
it either from the ieee80211_ba_session_work() wiphy work or from
ieee80211_sta_tear_down_BA_sessions() during station teardown.
Softirqs can run in that window too, both from the local_bh_enable() that
ends ieee80211_agg_start_txq() and from any interrupt exit, so the RCU
callback can free tid_tx before the read.
Driving the function from a test module with the grace period forced into
that window, KASAN reports the read, and the free arrives on the ordinary
RCU softirq path:
BUG: KASAN: slab-use-after-free in ieee80211_stop_tx_ba_cb+0x3cd/0x400
Read of size 1 at addr ffff888002b9f52e by task kworker/0:1/10
[...]
Freed by task 57:
__kasan_slab_free+0x47/0x70
__rcu_free_sheaf_prepare+0x70/0x250
rcu_free_sheaf_nobarn+0x18/0x40
rcu_core+0x426/0x1310
handle_softirqs+0x144/0x590
__irq_exit_rcu+0xea/0x150
irq_exit_rcu+0x9/0x20
sysvec_apic_timer_interrupt+0x6b/0x80
asm_sysvec_apic_timer_interrupt+0x1a/0x20
send_delba is only set when tx_stop is set, which happens for
AGG_STOP_LOCAL_REQUEST alone, so this is reached on local teardown -
session idle timeout, PTK rekey, suspend, HW reconfig - and not from a
peer's DELBA.
Read ndp into a local before the session is freed, while sta->lock is still
held. tid_tx->ndp has a single writer, in
ieee80211_tx_ba_session_handle_start(), which cannot run concurrently here:
both paths are serialised by the wiphy mutex, and the session is already
marked HT_AGG_STATE_STOPPING at this point. tid_tx->ndp is also the only
tid_tx dereference left after ieee80211_remove_tid_tx() in this function.
[move/change the comment a bit to be more general not just on ndp,
initialize ndp directly] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/page_reporting: use system_freezable_wq to fix UAF during suspend
During PM freeze (e.g. S3 suspend or S4 hibernation), device drivers like
virtio_balloon reset their underlying virtio devices and delete their
virtqueues via vdev->config->del_vqs().
However, page reporting work (page_reporting_process) was scheduled on the
global system_wq. Because system_wq lacks the WQ_FREEZABLE flag, the PM
freezer skips it, leaving page_reporting_process active during suspend.
If pages are freed into the buddy allocator while suspending (for example,
when core MM invokes the balloon shrinker during S4 hibernation image
saving), page reporting triggers virtballoon_free_page_report() on deleted
virtqueues, resulting in a Use-After-Free / General Protection Fault:
[ 196.795226] general protection fault, probably for non-canonical address 0xaa1436fe70dae6df: 0000 [#1] SMP NOPTI
[ 196.825967] Workqueue: events page_reporting_process
[ 196.831038] RIP: 0010:virtqueue_add_split+0x233/0x4c0 [virtio_ring]
[ 196.927073] virtballoon_free_page_report+0x3a/0xe0 [virtio_balloon]
[ 196.946943] page_reporting_process+0x370/0x4f0
Fix this by switching page reporting work to system_freezable_wq. This
ensures that the PM freezer pauses page_reporting_process before device
drivers destroy their reporting virtqueues. Because the reporting worker
is frozen, memory reclamation/freeing (e.g. via shrinker execution) can
safely return pages to MM during freeze without triggering unfrozen
reporting work on deleted virtqueues.
This aligns with the driver's existing design. The comment in
virtballoon_freeze() states:
/*
* The workqueue is already frozen by the PM core before this
* function is called.
*/
Testing:
I have verified these fixes using Google’s virtualization infrastructure
by running continuous suspend/resume iterations (40+ cycles) while
churning memory using stress-ng (`stress-ng --vm 4 --vm-bytes 60%
--timeout 1`) to constantly create free pages for the buddy allocator. We
also set the `page_reporting_order` parameter to 0 to make the page
reporting worker highly sensitive, forcing it to pick up any 4K free
pages. This confirmed that the UAF crashes are no longer reproducible. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: stop fast-leave after deleting a port group
br_multicast_leave_group() iterates mp->ports with pp = &p->next in
its fast-leave path. After br_multicast_del_pg() removes p,
continuing the loop advances pp through the deleted entry.
If multicast-to-unicast was enabled, the bridge can hold multiple port
groups for the same port and group with different source MAC
addresses. Once multicast-to-unicast is disabled,
br_port_group_equal() matches those entries by port only. A fast leave
can then delete one entry and continue from its stale next pointer,
leaving mp->ports pointing at a deleted port group.
Fast leave only needs to remove one matching port group. Break after
br_multicast_del_pg() so the loop stops before dereferencing the
removed entry. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Check return value of __register_event() in trace_module_add_events()
trace_module_add_events() ignores the return value of __register_event()
and unconditionally calls __add_event_to_tracers() for each event.
If __register_event() fails (for example, if event_init() fails), the
trace_event_call is not added to ftrace_events list, but
__add_event_to_tracers() still creates a trace_event_file pointing to it.
If module loading subsequently fails and module memory is freed, tracing
state retains a stale trace_event_call pointer in trace_event_file,
leading to a use-after-free when tracefs or tracing subsystem operations
are later executed.
Fix this by checking the return value of __register_event() and only
calling __add_event_to_tracers() if event registration succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix potential UAF on meter attach failure
While attaching a newly created meter attach_meter() function makes
the new meter visible to other CPUs but can still fail afterwards.
On failure, it detaches the meter back and returns an error.
However, this is an unexpected behavior for the ovs_meter_cmd_set()
that uses a plain kfree(meter) on attach failure without waiting for
RCU readers to stop using it, assuming it was never visible.
This is never a problem for ovs-vswitchd as it always creates meters
before creating any flows that use them. But the UAF can be triggered
with a custom application using uAPI:
BUG: KASAN: slab-use-after-free in ovs_meter_execute (net/openvswitch/meter.c:653)
Read of size 8 at addr ffff88810d152650 by task meter/2508
Call Trace:
ovs_meter_execute (net/openvswitch/meter.c:653)
do_execute_actions (net/openvswitch/actions.c:1407)
ovs_execute_actions (net/openvswitch/actions.c:1584)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:703)
...
netlink_sendmsg (af_netlink.c:1900)
Allocated by task 2519:
__kasan_kmalloc (mm/kasan/common.c:398 mm/kasan/common.c:415)
ovs_meter_cmd_set (net/openvswitch/meter.c:422)
...
netlink_sendmsg (af_netlink.c:1900)
Freed by task 2519:
kfree (mm/slub.c:2705 mm/slub.c:6405 mm/slub.c:6720)
ovs_meter_cmd_set (net/openvswitch/meter.c:479)
...
netlink_sendmsg (af_netlink.c:1900)
Fix that by making sure attach_meter() doesn't make the meter visible
until all the checks are done and the function can't fail anymore.
This also makes sure the "hash" value is calculated after the potential
re-sizing of the table.
Reported by Trend Micro's Zero Day Initiative as ZDI-CAN-31642. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: fix pptable use-after-free
amdgpu_dpm_get_pp_table() returns a pointer to a driver-owned power table
after dropping adev->pm.mutex. The sysfs path then copies from that pointer.
A concurrent pp_table write can replace and free the allocation during the
copy, causing a use-after-free.
Change the DPM interface to copy into caller-provided storage while the mutex
is held. Keep the size-only query for attribute discovery without exposing
the driver-owned pointer.
(cherry picked from commit f6eed7acfd30099ef7baeb6ba45bb59daad80631) |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: serialize kernel accept preallocation with socket teardown
rxrpc_kernel_charge_accept() reads rx->backlog without any
socket/backlog synchronization and passes that raw pointer into
rxrpc_service_prealloc_one(). A concurrent rxrpc_discard_prealloc()
sets rx->backlog = NULL and frees the backlog rings, so a kernel
preallocation worker can keep using a freed struct rxrpc_backlog
while updating *_backlog_head/tail and array slots.
Serialize the state check and backlog lookup with the socket lock,
and reject kernel preallocation once teardown has disabled
listening or discarded the service backlog. |
| In the Linux kernel, the following vulnerability has been resolved:
dlm: fix add msg handle in send_queue ordered
In a benchmark scenario triggering a lot of requests that triggers a lot
of DLM messages on the network it can be that the mh->seq is not ordered
according the oldest seq number. This ordering is required by
dlm_receive_ack as "before(mh->seq, seq)" will stop to check for older
sequence numbers that are ordered in the tail of "node->send_queue".
The side effects of not having it correct ordered regarding
"before(mh->seq, seq)" are refcounting issues and use-after free.
I only was able to reproduce this issue in a experimental DLM branch
and a user space DLM benchmark that uses io_uring. After changing this I
don't experienced any refcounting with the sending buffer issues anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: oss: Fix UAF at handling events with embedded SysEx data
The OSS sequencer processes the input MIDI bytes into a sequencer
event to be dispatched later (in snd_seq_oss_midi_putc() called from
snd_seq_oss_process_event()). When it's a SysEx data, the event
record contains data.ext.ptr pointer to the original SysEx bytes, and
the referred data is copied into the pool afterwards at dispatching.
The problem is that, if the sequencer port gets closed concurrently
before the dispatch, the OSS sequencer core also releases the
resources (in snd_seq_oss_midi_check_exit_port()), while the pending
event may hold a stale pointer, eventually leading to a UAF at a later
dispatch.
Fortunately, there is already a refcounting mechanism (snd_use_lock_t)
for the OSS MIDI device access, and for addressing the issue above, we
just need to extend the refcount until the event gets dispatched.
This patch extends snd_seq_oss_process_event() to give back the
refcount object, which is in turn released after calling the sequencer
dispatcher with the given event in the caller side.
According to the original report, KASAN report as below:
KASAN slab-use-after-free in snd_seq_event_dup+0x40c/0x470
RIP: 0033:0x7f2cb66a6340
Read of size 6
Call trace:
dump_stack_lvl+0x73/0xb0 (?:?)
print_report+0xd1/0x650 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x1a7/0x340 (?:?)
kasan_complete_mode_report_info+0x64/0x200 (?:?)
kasan_report+0xf7/0x130 (?:?)
snd_seq_event_dup+0x40c/0x470 (?:?)
kasan_check_range+0x10c/0x1c0 (?:?)
__asan_memcpy+0x27/0x70 (?:?)
snd_seq_event_dup+0x9/0x470 (?:?)
snd_seq_client_enqueue_event+0x139/0x240 (?:?)
_raw_spin_unlock_irqrestore+0x4b/0x60 (?:?)
snd_seq_kernel_client_enqueue+0x102/0x120 (?:?)
snd_seq_oss_write+0x416/0x4e0 (?:?)
apparmor_file_permission+0x20/0x30 (?:?)
odev_write+0x3b/0x60 (?:?)
vfs_write+0x1ce/0x850 (?:?)
lock_release+0xc8/0x2a0 (?:?)
__kasan_check_write+0x18/0x20 (?:?)
__mutex_unlock_slowpath+0x129/0x510 (?:?)
ksys_write+0xe1/0x180 (?:?)
mutex_unlock+0x16/0x20 (?:?)
odev_ioctl+0x65/0xc0 (?:?)
__x64_sys_write+0x46/0x60 (?:?)
x64_sys_call+0x7d/0x20d0 (?:?)
do_syscall_64+0xc1/0x360 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?) |
| Untrusted pointer dereference in Windows COM+ Event System Service allows an authorized attacker to elevate privileges locally. |
| Ivanti Connect Secure 22.8R2.4 mishandles the manner in which the dsinvoked broker trusts DSCache configuration data, leading to privilege escalation to root, as exploited in the wild in October 2026. |
| Untrusted pointer dereference in Windows Win32 Kernel Subsystem allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Fix RB-tree corruption in probe error path
The info->node RB-tree member is zero-initialized via kzalloc. If
a device does not support ATS, the device_rbtree_insert() call is
skipped. If a subsequent probe step fails, the error path jumps to
device_rbtree_remove(), which misinterprets the zeroed node as
a tree root and corrupts the device RB-tree.
Fix this by explicitly initializing the RB-node as empty using
RB_CLEAR_NODE() during initialization and guarding the removal with
RB_EMPTY_NODE(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Clear rb node linkage when freeing bpf_rb_root
bpf_rb_root_free() detaches the root by copying the current rb_root_cached
and then replacing the live root with RB_ROOT_CACHED. It then walks the
copied root and drops each object contained in the tree.
This leaves the rb node state intact while dropping the object. If the
object is refcounted and survives the drop, its bpf_rb_node_kern still
contains an owner pointer to the freed root and stale rb tree linkage. If
a later bpf_rb_root allocation reuses the same address, bpf_rbtree_remove()
can incorrectly pass the owner check and call rb_erase_cached() on a node
whose rb pointers belong to the old tree.
Mirror the list draining behavior by marking nodes as busy while the root
is being detached, then clear the rb node and release the owner before
dropping the containing object. This makes surviving nodes unowned and
safe to reject from remove or accept for a later add. |
| In the Linux kernel, the following vulnerability has been resolved:
net: watchdog: fix refcount tracking races
Blamed commit converted the untracked dev_hold()/dev_put() calls
in the watchdog code to use the tracked dev_hold_track()/dev_put_track()
(which were later renamed/interfaced to netdev_hold() and netdev_put()).
By introducing dev->watchdog_dev_tracker to store the
reference tracking information without adding synchronization
between netdev_watchdog_up() and dev_watchdog(), it enabled the
race condition where this pointer could be overwritten or freed
concurrently, leading to the list corruption crash syzbot reported:
list_del corruption, ffff888114a18c00->next is NULL
kernel BUG at lib/list_debug.c:52 !
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 1 UID: 0 PID: 91 Comm: kworker/u8:5 Not tainted syzkaller #0 PREEMPT(lazy)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/09/2026
Workqueue: events_unbound linkwatch_event
RIP: 0010:__list_del_entry_valid_or_report.cold+0x22/0x2a lib/list_debug.c:52
Call Trace:
<TASK>
__list_del_entry_valid include/linux/list.h:132 [inline]
__list_del_entry include/linux/list.h:246 [inline]
list_move_tail include/linux/list.h:341 [inline]
ref_tracker_free+0x1a7/0x6c0 lib/ref_tracker.c:329
netdev_tracker_free include/linux/netdevice.h:4491 [inline]
netdev_put include/linux/netdevice.h:4508 [inline]
netdev_put include/linux/netdevice.h:4504 [inline]
netdev_watchdog_down net/sched/sch_generic.c:600 [inline]
dev_deactivate_many+0x28c/0xfe0 net/sched/sch_generic.c:1363
dev_deactivate+0x109/0x1d0 net/sched/sch_generic.c:1397
linkwatch_do_dev net/core/link_watch.c:184 [inline]
linkwatch_do_dev+0xd3/0x120 net/core/link_watch.c:166
__linkwatch_run_queue+0x3a5/0x810 net/core/link_watch.c:240
linkwatch_event+0x8f/0xc0 net/core/link_watch.c:314
process_one_work+0xa0e/0x1980 kernel/workqueue.c:3314
process_scheduled_works kernel/workqueue.c:3397 [inline]
worker_thread+0x5ef/0xe50 kernel/workqueue.c:3478
kthread+0x370/0x450 kernel/kthread.c:436
ret_from_fork+0x69a/0xc80 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
This patch has three coordinated parts:
1) Add dev->watchdog_lock and dev->watchdog_ref_held to serialize watchdog operations.
2) Remove netdev_watchdog_up() call from netif_carrier_on():
This ensures netdev_watchdog_up() is only called from process/BH context
(via linkwatch workqueue dev_activate()), allowing us to use
spin_lock_bh() for synchronization.
3) Synchronize watchdog up and watchdog timer:
Protect netdev_watchdog_up() with tx_global_lock and watchdog_lock.
Only allocate a new tracker in netdev_watchdog_up() if one is
not already present.
In dev_watchdog(), ensure we don't release the tracker if the
timer was rescheduled either by dev_watchdog() itself or concurrently
by netdev_watchdog_up(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Free CQ toggle page after firmware teardown
Free the toggle page only after firmware teardown completes so that
an NQ interrupt arriving during bnxt_qplib_destroy_cq() won't write
the toggle value to an already-freed page. Move free_page() after
bnxt_qplib_destroy_cq. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: Fix possible use after free
In dma_release_channel(), check chan->device->privatecnt after call
dma_chan_put(). However, dma_chan_put() call dma_device_put() which could
release the last reference of the device if the DMA provider is already
gone and hence free it.
Fixes it by moving dma_chan_put() after the check. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: make sure gc is properly stopped
Sashiko noticed that when destroying a set,
cancel_delayed_work_sync() was called while gc
calls queue_delayed_work() unconditionally which
can lead not to properly shutting down the gc. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: stp: Fix a potential use-after-free when deleting a bridge
The three STP timers are not supposed to be armed while the bridge is
administratively down. They are synchronously deactivated when the
bridge is put administratively down and the various call sites check for
'IFF_UP' before arming them.
This check is missing from br_topology_change_detection() and it is
possible to engineer a situation in which the topology change timer is
armed while the bridge is administratively down, resulting in a
use-after-free [1] when the bridge is deleted.
Fix by adding the missing check and for good measures synchronously
shutdown the three timers when the bridge is deleted.
[1]
ODEBUG: free active (active state 0) object: ffff88811662b9b0 object type: timer_list hint: br_topology_change_timer_expired (net/bridge/br_stp_timer.c:120)
WARNING: lib/debugobjects.c:629 at debug_print_object+0x1bc/0x450, CPU#9: ip/359 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix HV VHCA stats agent registration race
mlx5e_hv_vhca_stats_create() registers the stats agent through
mlx5_hv_vhca_agent_create(). The helper publishes the agent in
hv_vhca->agents[type] under agents_lock and immediately schedules an
asynchronous control invalidation on the HV VHCA workqueue before
returning to mlx5e.
The asynchronous invalidation invokes the control agent's invalidate
callback, which reads the hypervisor control block and forwards the
command to mlx5e_hv_vhca_stats_control(). That callback may either:
- call cancel_delayed_work_sync(&priv->stats_agent.work), or
- call queue_delayed_work(priv->wq, &sagent->work, sagent->delay).
However, the delayed_work and priv->stats_agent.agent are only
initialized after mlx5_hv_vhca_agent_create() returns to mlx5e:
agent = mlx5_hv_vhca_agent_create(...); /* publish + invalidate */
...
priv->stats_agent.agent = agent; /* too late */
INIT_DELAYED_WORK(&priv->stats_agent.work, ...); /* too late */
If the asynchronous control path runs before the two assignments
above, it can:
- Operate on an uninitialized delayed_work whose timer.function is
NULL. queue_delayed_work() calls add_timer() unconditionally, so
when the timer expires the timer softirq invokes a NULL function
pointer.
- Re-initialize the timer later through INIT_DELAYED_WORK() while
the timer is already enqueued in the timer wheel, corrupting the
hlist (entry.pprev cleared while the previous bucket node still
points at this entry).
- When the worker eventually runs, mlx5e_hv_vhca_stats_work() reads
sagent->agent (NULL) and dereferences it inside
mlx5_hv_vhca_agent_write().
Fix this by:
- Initializing priv->stats_agent.work before invoking
mlx5_hv_vhca_agent_create(), so the work is always in a valid
state when the control callback observes it.
- Adding a struct mlx5_hv_vhca_agent **ctx_update out-parameter
to mlx5_hv_vhca_agent_create(). The helper writes the agent
pointer to *ctx_update before publishing into hv_vhca->agents[]
and triggering the agents_update flow, so any callback
subsequently invoked from that flow already sees a valid
priv->stats_agent.agent. This avoids having the control
callback participate in agent initialization.
While at it, access priv->stats_agent.agent with
READ_ONCE()/WRITE_ONCE() for the cross-CPU access with the worker, and
clear priv->stats_agent.buf on the agent_create() failure path. |
