| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: mt7621: avoid corruption of shared interrupt trigger state
The bank-shared fields like 'rising' and 'falling' are modified using
non-atomic read-modify-write operations. Since every gpio chip instance
represents an entire bank of 32 pins, if 'mediatek_gpio_irq_type()' is
called concurrently for different IRQs on the same bank a possible overwrite
of each other's configuration is possible. Thus, protect this state with
'gpio_generic_lock_irqsave' lock in the same way it is handled in irp_chip
'mediatek_gpio_irq_mask()' and 'mediatek_gpio_irq_unmask()' callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/virt/sev: Revert "Drop WBINVD before setting MSR_AMD64_SYSCFG_SNP_EN"
Revert
99cf1fb58e68 ("x86/virt/sev: Drop WBINVD before setting MSR_AMD64_SYSCFG_SNP_EN").
Section 8.8 of the SNP spec says:
Before invoking SNP_INIT_EX with INIT_RMP set to 1, software must ensure
that no CPUs contain dirty cache lines for the memory containing the RMP.
Cachelines can be moved from cache to cache in a dirty state. The
wbinvd_on_all_cpus() before SNP_INIT_EX flushes the caches for each CPU, but
if the IPIs for WBINVD race with this dirty cacheline movement, it is possible
that they may not get flushed, violating the firmware requirement.
Doing wbinvd_on_all_cpus() before setting SNPEn is safer since the RMP
table is not yet in use.
[ Heroically bisected by Srikanth. ]
[ bp: Massage commit message. ] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/fb-helper: Only consider active CRTCs for vblank sync
Only synchronize fbdev output to the vblank of an active CRTC. Go over
the list of CRTCs and pick the first that matches. Fixes warnings as
the one shown below
[ 77.201354] WARNING: drivers/gpu/drm/drm_vblank.c:1320 at drm_crtc_wait_one_vblank+0x194/0x1cc [drm], CPU#1: kworker/1:7/1867
[ 77.201354] omapdrm omapdrm.0: [drm] vblank wait timed out on crtc 0
This currently happens if the fbdev output is not on CRTC 0.
Atomic and non-atomic drivers require distinct code paths. As for other
fbdev operations, implement both and select the correct one at runtime.
Not finding an active CRTC is not a bug. Do not wait in this case, but
flush the display update as before.
v4:
- avoid possible deadlocks with locking context (Sashiko)
v3:
- drop excessive state validation (Jani)
- acquire plane and CRTC mutices (Sashiko)
v2:
- move look-up code into separate helper
- support drivers with legacy modesetting
v1:
- see https://lore.kernel.org/dri-devel/1c9e0e24-9c4a-4259-8700-cf9e5fd60ca3@suse.de/ |
| In the Linux kernel, the following vulnerability has been resolved:
nvdimm/btt: Handle preemption in BTT lane acquisition
BTT lanes serialize access to per-lane metadata and workspace state
during BTT I/O. The btt-check unit test reports data mismatches during
BTT writes due to a race in lane acquisition that can lead to silent
data corruption.
The existing lane model uses a spinlock together with a per-CPU
recursion count. That recursion model stopped being valid after BTT
lanes became preemptible: another task can run on the same CPU,
observe a non-zero recursion count, bypass locking, and use the same
lane concurrently.
BTT lanes are also held across arena_write_bytes() calls. That path
reaches nsio_rw_bytes(), which flushes writes with nvdimm_flush().
Some provider flush callbacks can sleep, making a spinlock the wrong
primitive for the lane lifetime.
Replace the spinlock-based recursion model with a dynamically
allocated per-lane mutex array and take the lane lock
unconditionally.
Add might_sleep() to catch any future atomic-context caller.
Found with the ndctl unit test btt-check.sh. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: mark I2C adapter when hardware is powered down
On some i.MX platforms, certain I2C client drivers keep a periodic
workqueue which continues to trigger I2C transfers.
During system suspend/resume, there exists a time window between:
- suspend_noirq and the system entering suspend
- the system starting to resume and resume_noirq
In this window, the I2C controller resources such as clock and pinctrl
may already be disabled or not yet restored.
If a workqueue triggers an I2C transfer in this period, the driver
attempts to access I2C registers while the hardware resources are
unavailable, which may lead to system hang.
Mark the I2C adapter as suspended during noirq suspend and block new
transfers until resume, ensuring that I2C transfers are only issued
when hardware resources are available. |
| Use-after-free in the Layout: Text and Fonts component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: extend bcm_tx_lock usage for data and timer updates
Stage new CAN frame content for an existing tx op into a kmalloc()'d
buffer and validate it there, mirroring the approach already used in
bcm_rx_setup(). Only copy the validated data into op->frames while
holding op->bcm_tx_lock, so bcm_can_tx() and bcm_tx_timeout_handler()
can no longer observe a partially updated or unvalidated frame.
Add a missing error path for memcpy_from_msg() when copying CAN frame
data from userspace.
Also move the kt_ival1/kt_ival2/ival1/ival2 updates in bcm_tx_setup()
under op->bcm_tx_lock, and read kt_ival1/kt_ival2/count under the same
lock in bcm_tx_set_expiry() and bcm_tx_timeout_handler(), closing the
torn 64-bit ktime_t read on 32-bit platforms. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix CAN frame rx/tx statistics
KCSAN detected a data race within the bcm_rx_handler() when two CAN frames
have been simultaneously received and processed in a single rx op by two
different CPUs.
Use atomic operations with (signed) long data types to access the
statistics in the hot path to fix the KCSAN complaint.
Additionally simplify the update and check of statistics overflow by
using the atomic operations in separate bcm_update_[rx|tx]_stats()
functions. The rx variant runs under bcm_rx_update_lock to prevent
races when resetting the two rx counters; the tx variant runs under
bcm_tx_lock and only needs to guard its own counter's overflow.
As the rx path resets its values already at LONG_MAX / 100, there is
no conflict between the two locking domains (bcm_rx_update_lock vs.
bcm_tx_lock) even for ops that use both paths.
The rx statistics update and the frames_filtered update in
bcm_rx_changed() were previously performed in two separate
bcm_rx_update_lock sections. For an rx op subscribed on all interfaces
(ifindex == 0), bcm_rx_handler() can run concurrently on different
CPUs, so a counter reset by one CPU between these two sections could
leave frames_filtered larger than frames_abs on another CPU, producing
a bogus (even negative) reduction percentage in procfs. Update the
statistics in the same critical section as bcm_rx_changed() to close
this gap, which also removes the now unneeded extra lock/unlock pair
around the traffic_flags calculation. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: track a single source interface for ANYDEV timeout/throttle ops
An ANYDEV rx op (ifindex == 0) with an active RX timeout and/or
throttle timer has no defined semantics when matching frames arrive
from several interfaces: bcm_rx_handler() can run concurrently for
the same op on different CPUs, racing hrtimer_cancel()/
bcm_rx_starttimer() against bcm_rx_timeout_handler() and causing
spurious RX_TIMEOUT notifications and last_frames corruption. The
same concurrency lets throttled multiplex frames from different
interfaces clobber the single rx_ifindex/rx_stamp fields shared by
the op.
Add op->if_detected to track the first interface that delivers a
matching frame while a timeout/throttle timer is configured, and
reject frames from any other interface for that op. The claim is
decided in bcm_rx_handler() before hrtimer_cancel() touches
op->timer, so a rejected frame can never disturb the claimed
interface's watchdog. RTR-mode ops are excluded via RX_RTR_FRAME,
independent of kt_ival1/kt_ival2, since those may briefly hold a
stale value from an earlier non-RTR configuration.
The claim is released in bcm_notify() on NETDEV_UNREGISTER and in
bcm_rx_setup() when SETTIMER reconfigures the timer values.
A (re-)claim is only possible on CAN devices in NETREG_REGISTERED
dev->reg_state to cover the release in bcm_notify() where reg_state
becomes NETREG_UNREGISTERING until synchronize_net(). |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: use WRITE_ONCE() when changing lower socket callbacks
kcm_attach() replaces a live lower TCP socket's sk_data_ready and
sk_write_space callbacks with KCM handlers, and kcm_unattach() restores
them later. Those callback-pointer updates are still plain stores even
though the same fields can be read and invoked concurrently on other
CPUs.
If another CPU observes an older callback snapshot after the live field
has already been restored, callback execution can run with a mismatched
target and sk_user_data state, leading to stale or misdirected wakeups.
Use WRITE_ONCE() for the callback replacement and restore operations so
these shared callback fields follow the same visibility contract already
established by the earlier 4022 fixes. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: fix permanently busy scans after multiple roam iterations
In order for the firmware to sleep, the driver has to confirm a
previously received sleep request. The normal sequence of evets goes
like this:
EVENT_SLEEP -> adapter->ps_state = PS_STATE_PRE_SLEEP -> sleep-confirm
-> SLEEP -> EVENT_AWAKE -> AWAKE.
Before sending the sleep-confirm command, the driver must make sure
there are no commands either running or waiting to be completed.
mwifiex_ret_802_11_associate() unconditionally sets
ps_state = PS_STATE_AWAKE when it processes the association command
response, outside of the normal powersave management flow. If
EVENT_SLEEP arrives while the association command is in flight,
ps_state is PRE_SLEEP when the association command response is parsed,
and the forced AWAKE overwrites it. The deferred sleep-confirm is
never sent.
A subsequent scan_start command is correctly acknowledged, but the
firmware doesn't generate scan_result events. The scan request never
finishes, and additional requests from userspace fail with -EBUSY.
After testing on both IW412 and W8997, I could only trigger the bug on
the IW412 and observed the firmwares behave differently. On the IW412
the firmware still sends EVENT_SLEEP while the authentication /
association process is ongoing. A W8997 under the same
conditions seems to suppress power-save for the duration of the
association, so PRE_SLEEP never coincided with the association response
even after extended periods of testing using the loops
described below (>12hours).
On the IW412, the delay between commands that triggers an EVENT_SLEEP
was empirically determined to be ~20ms. This delay can naturally occur
when the driver is outputting debugging information
(debug_mask = 0x00000037), in which situation the busy scans issue is
repeatable while running "test 1)" as described below. If the delay
between commands is less than ~20ms, the firmware stays awake and
the issue was not reproducible running the same test.
The host_mlme=false path also behaves differently. In this case, the
entire authentication / association transaction is executed by one
command (HostCmd_CMD_802_11_ASSOCIATE), and the firmware doesn't emit
EVENT_SLEEP while the command is running.
Remove the assignment so the ps_state is only manipulated in the paths
that are related to powersave event handling and on the main workqueue
for correct sleep confirmation.
The following loop tests were performed (with debugging output enabled):
1) force roaming between two AP's, one 5GHz and one 2.4GHz, same
SSID. Use wpa_cli to trigger the roaming behavior, sleep 2s
between iterations.
2) force a disconnection to AP 1 and a connection to AP 2, test
scan. Use wpa_cli to trigger the connection changes, sleep 2s
between iterations.
Each test ran in each device for at least 3 hours. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect()
ueagle-atm uses the asynchronous request_firmware_nowait() in .probe(),
but does not wait for its completion, not even in .disconnect(); so, if the
device is unplugged meanwhile, its teardown runs concurrently with that.
Even though this inconsistency is worth addressing on its own, it has also
triggered several bug reports in syzbot over the years (some auto-closed)
where the firmware sysfs fallback mechanism (CONFIG_FW_LOADER_USER_HELPER)
creates a firmware subdirectory in the device directory during its removal,
which might hit unexpected conditions in kernfs, apparently, depending at
which point the add and remove operations raced. (See links.)
The pattern is:
usb ?-?: Direct firmware load for ueagle-atm/eagle?.fw failed with error -2
usb ?-?: Falling back to sysfs fallback for: ueagle-atm/eagle?.fw
<ERROR>
Call trace:
...
kernfs_create_dir_ns
sysfs_create_dir_ns
create_dir
kobject_add_internal
kobject_add_varg
kobject_add
class_dir_create_and_add
get_device_parent
device_add
fw_load_sysfs_fallback
fw_load_from_user_helper
firmware_fallback_sysfs
_request_firmware
request_firmware_work_func
...
(Some variations are observed, after fw_load_sysfs_fallback(), e.g., [1].)
While the kernfs side is being looked at, the ueagle-atm side can be fixed
by waiting for the pre-firmware load in the .disconnect() handler.
This change has a similar approach to previous work by Andrey Tsygunka [2]
(wait_for_completion() in .disconnect()), but it is relatively different in
design/implementation; using the Originally-by tag for credit assignment.
This has been tested with:
- synthetic reproducer to check the error path;
- USB gadget (virtual device) to check the firmware upload path;
- QEMU device emulator to check the device ID re-enumeration path;
(The latter two were written by Claude; no other code/text in this commit.)
Links (year first reported):
2025 https://syzbot.org/bug?extid=ce1e5a1b4e086b43e56d
2025 https://syzbot.org/bug?extid=9af8471255ac36e34fd4
2024 https://syzbot.org/bug?extid=306212936b13e520679d
2023 https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
2022 https://syzbot.org/bug?extid=782984d6f1701b526edb
2021 https://syzbot.org/bug?id=f3f221579f4ef7e9691281f3c6f56c05f83e8490
2021 https://syzbot.org/bug?id=84d86f0d71394829df6fc53daf6642c045983881
2021 https://syzbot.org/bug?id=3302dc1c0e2b9c94f2e8edb404eabc9267bc6f90
[1] https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
[2] https://lore.kernel.org/lkml/20250410093146.3776801-2-aitsygunka@yandex.ru/ |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: fix io_thread race in rxrpc_wake_up_io_thread()
rxrpc_wake_up_io_thread() checks local->io_thread before waking it, but
then reloads the pointer for wake_up_process().
local->io_thread is cleared with WRITE_ONCE() when the I/O thread exits, so
the second load can see NULL even if the first load did not.
Take a READ_ONCE() snapshot and use it for both the NULL check and the
wake_up_process() call, as rxrpc_encap_rcv() already does. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: wake eh reliably when using scsi_schedule_eh
Drivers which use the scsi_schedule_eh function to run the error handler
currently risk the error handler thread never waking once all commands are
timed out or inactive. There is no enforced memory order between setting
the host into error recovery state and counting busy commands. This can
result in a race with scsi_dec_host_busy where neither CPU sees both
conditions of all commands inactive and the host error state to request
waking the error handler.
To fix this, run the scsi_schedule_eh's scsi_eh_wakeup from a new work item
which will use rcu to ensure scsi_schedule_eh's call to scsi_host_busy will
occur after the error state is globally visible and will be seen by any
current scsi_dec_host_busy callers. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix UAF in binder_free_transaction()
In binder_free_transaction(), the t->to_proc is read under the t->lock.
However, once the t->lock is dropped, the to_proc can die in parallel.
This leads to a use-after-free error when we attempt to acquire its
inner lock right afterwards:
==================================================================
BUG: KASAN: slab-use-after-free in _raw_spin_lock+0xe4/0x1a0
Write of size 4 at addr ffff00001125da70 by task B/672
CPU: 20 UID: 0 PID: 672 Comm: B Not tainted 7.1.0-rc6-00284-g8e65320d91cd #4 PREEMPT
Hardware name: linux,dummy-virt (DT)
Call trace:
_raw_spin_lock+0xe4/0x1a0
binder_free_transaction+0x8c/0x320
binder_send_failed_reply+0x21c/0x2f8
binder_thread_release+0x488/0x7e0
binder_ioctl+0x12c0/0x29a0
[...]
Allocated by task 675:
__kmalloc_cache_noprof+0x174/0x444
binder_open+0x118/0xb70
do_dentry_open+0x374/0x1040
vfs_open+0x58/0x3bc
[...]
Freed by task 212:
__kasan_slab_free+0x58/0x80
kfree+0x1a0/0x4a4
binder_proc_dec_tmpref+0x32c/0x5e0
binder_deferred_func+0xc48/0x104c
process_one_work+0x53c/0xbc0
[...]
==================================================================
To prevent this, pin the target thread (t->to_thread) to guarantee the
target process remains alive. Undelivered transactions without a target
thread are already safe, as the target process can only be the current
context in those paths. |
| Race in V8 in Google Chrome prior to 151.0.7922.72 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: Low) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gem: fix race between change_handle and handle_delete
drm_gem_change_handle_ioctl leaves the old handle live in the IDR
during the window between spin_unlock(table_lock) and the final
spin_lock(table_lock). A concurrent drm_gem_handle_delete on the old
handle succeeds in this window, decrements handle_count to 0, and frees
the GEM object while the new handle's IDR entry still references it.
NULL the old handle's IDR entry before dropping table_lock so that any
concurrent GEM_CLOSE on the old handle sees NULL and returns -EINVAL.
Restore the old entry on the prime-bookkeeping error path. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Set HCI_CMD_DRAIN_WORKQUEUE during device close
Since hci_dev_close_sync() can now be called during the reset path, we
should also set HCI_CMD_DRAIN_WORKQUEUE. This avoids queuing timeouts
while the hdev workqueue is being drained. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_fs: serialize DMABUF cancel against request completion
ffs_epfile_dmabuf_io_complete() calls usb_ep_free_request() on the
completed request but leaves priv->req, the back-pointer that
ffs_dmabuf_transfer() set on submission, pointing at the freed
memory. A later FUNCTIONFS_DMABUF_DETACH ioctl or
ffs_epfile_release() on the close path still sees priv->req
non-NULL under ffs->eps_lock:
if (priv->ep && priv->req)
usb_ep_dequeue(priv->ep, priv->req);
so usb_ep_dequeue() is called on a freed usb_request.
On dummy_hcd the dequeue path only walks a live queue and
pointer-compares, so the freed pointer reads without faulting and
KASAN requires an explicit check at the FunctionFS call site to
surface the use-after-free. On SG-capable in-tree UDCs the
dequeue path dereferences the supplied request immediately:
* chipidea's ep_dequeue() does
container_of(req, struct ci_hw_req, req) and reads
hwreq->req.status before acquiring its own lock.
* cdnsp's cdnsp_gadget_ep_dequeue() reads request->status first.
The narrower option of clearing priv->req via cmpxchg() in the
completion does not close the race: the completion runs without
eps_lock, so a cancel path holding eps_lock can still observe
priv->req non-NULL, race a concurrent completion that clears and
frees, and pass the freed pointer to usb_ep_dequeue(). A slightly
longer fix that moves the free into the cleanup work is needed.
Same class of lifetime race as the recent usbip-vudc timer fix [1].
Take eps_lock in the sole place that mutates priv->req from the
callback direction by moving usb_ep_free_request() out of the
completion into ffs_dmabuf_cleanup(), the existing work handler
scheduled by ffs_dmabuf_signal_done() on
ffs->io_completion_wq. Clear priv->req there under eps_lock
before freeing, and only clear if priv->req still names our
request (a subsequent ffs_dmabuf_transfer() on the same
attachment may have queued a new one).
This keeps the existing dummy_hcd sync-dequeue invariant: the
completion callback is still invoked by the UDC without
eps_lock held (dummy_hcd drops its own lock before calling the
callback), and the callback now takes no f_fs lock at all.
Serialization against the cancel path happens in cleanup, which
runs from the workqueue with no f_fs lock held on entry.
The priv ref count protects the containing ffs_dmabuf_priv:
ffs_dmabuf_transfer() takes a ref via ffs_dmabuf_get(), cleanup
drops it via ffs_dmabuf_put(), so priv stays live for the
cleanup even after the cancel path's list_del + ffs_dmabuf_put.
The ffs_dmabuf_transfer() error path no longer frees usb_req
inline: fence->req and fence->ep are set before usb_ep_queue(),
so ffs_dmabuf_cleanup() (scheduled by the error-path
ffs_dmabuf_signal_done()) owns the free regardless of whether
the queue succeeded.
Reproduced under KASAN on both detach and close paths against
dummy_hcd with an observability hook
(kasan_check_byte(priv->req) immediately before usb_ep_dequeue)
at the two FunctionFS cancel sites to surface the stale-pointer
access; the hook is not part of this patch. The KASAN
allocator / free stacks in the captured splats identify the
same request: alloc in dummy_alloc_request, free in
dummy_timer, fault reached from ffs_epfile_release (close) and
from the FUNCTIONFS_DMABUF_DETACH ioctl (detach). With the
patch applied, both paths are silent under the same hook.
The bug is reached from the FunctionFS device node, which in
real deployments is owned by the privileged gadget daemon
(adbd, UMS, composite gadget services, etc.); it is not
reachable from unprivileged userspace or from a USB host on the
cable. FunctionFS mounts default to GLOBAL_ROOT_UID, but the
filesystem supports uid=, gid=, and fmode= delegation to a
non-root gadget daemon, so on real deployments the attacker may
be a less-privileged service rather than root. |
