| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: debugfs: fix out-of-bounds read in spi_nor_params_show()
Sashiko noticed an out-of-bounds read [1].
In spi_nor_params_show(), the snor_f_names array is passed to
spi_nor_print_flags() using sizeof(snor_f_names).
Since snor_f_names is an array of pointers, sizeof() returns the total
number of bytes occupied by the pointers
(element_count * sizeof(void *))
rather than the element count itself. On 64-bit systems, this makes the
passed length 8x larger than intended.
Inside spi_nor_print_flags(), the 'names_len' argument is used to
bounds-check the 'names' array access. An out-of-bounds read occurs
if a flag bit is set that exceeds the array's actual element count
but is within the inflated byte-size count.
Correct this by using ARRAY_SIZE() to pass the actual number of
string pointers in the array. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: b43legacy: enforce bounds check on firmware key index in RX path
Same fix as b43: the firmware-controlled key index in b43legacy_rx()
can exceed dev->max_nr_keys. The existing B43legacy_WARN_ON is
non-enforcing in production builds, allowing an out-of-bounds read of
dev->key[].
Make the check enforcing by dropping the frame for invalid indices. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix a potential clc buffer length underflow
The buf_len is used to limit the iterations for retrieving the country
power setting and may underflow under certain conditions due to changes
in the power table in CLC.
This underflow leads to an almost infinite loop or an invalid power
setting resulting in driver initialization failure. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: b43: enforce bounds check on firmware key index in b43_rx()
The firmware-controlled key index in b43_rx() can exceed the dev->key[]
array size (58 entries). The existing B43_WARN_ON is non-enforcing in
production builds, allowing an out-of-bounds read.
Make the B43_WARN_ON check enforcing by dropping the frame when the
firmware returns an invalid key index. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: reject zero shift in nft_bitwise
Reject zero shift operands for nft_bitwise left and right shift
expressions during initialization.
The carry propagation logic computes the carry from the adjacent 32-bit
word using BITS_PER_TYPE(u32) - shift. A zero shift operand turns this
into a 32-bit shift, which is undefined behaviour.
Reject zero shift operands in the control plane, alongside the existing
check for values greater than or equal to 32, so malformed rules never
reach the packet path. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmasm: fix heap over-read in ibmasm_send_i2o_message()
The ibmasm_send_i2o_message() function uses get_dot_command_size() to
compute the byte count for memcpy_toio(), but this value is derived from
user-controlled fields in the dot_command_header (command_size: u8,
data_size: u16) and is never validated against the actual allocation size.
A root user can write a small buffer with inflated header fields, causing
memcpy_toio() to read up to ~65 KB past the end of the allocation into
adjacent kernel heap, which is then forwarded to the service processor
over MMIO.
Silently clamping the copy size is not sufficient: if the header fields
claim a larger size than the buffer, the SP receives a dot command whose
own header is inconsistent with the I2O message length, which can cause
the SP to desynchronize. Reject such commands outright by returning
failure.
Validate command_size before calling get_mfa_inbound() to avoid leaking
an I2O message frame: reading INBOUND_QUEUE_PORT dequeues a hardware
frame from the controller's free pool, and returning without a
corresponding set_mfa_inbound() call would permanently exhaust it.
Additionally, clamp command_size to I2O_COMMAND_SIZE before the
memcpy_toio() so the MMIO write stays within the I2O message frame,
consistent with the clamping already performed by outgoing_message_size()
for the header field. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix deadlock with check operation and nowait requests
When an array check is running it will raise the barrier at which point
normal requests will become blocked and increment the nr_pending value to
signal there is work pending inside of wait_barrier(). NOWAIT requests
do not block and so will return immediately with an error, and additionally
do not increment nr_pending in wait_barrier(). Upstream change commit
43806c3d5b9b ("raid10: cleanup memleak at raid10_make_request") added a
call to raid_end_bio_io() to fix a memory leak when NOWAIT requests hit
this condition. raid_end_bio_io() eventually calls allow_barrier() and
it will unconditionally do an atomic_dec_and_test(&conf->nr_pending) even
though the corresponding increment on nr_pending didn't happen in the
NOWAIT case.
This can be easily seen by starting a check operation while an application
is doing nowait IO on the same array. This results in a deadlocked state
due to nr_pending value underflowing and so the md resync thread gets stuck
waiting for nr_pending to == 0.
Output of r10conf state of the array when we hit this condition:
crash> struct r10conf
barrier = 1,
nr_pending = {
counter = -41
},
nr_waiting = 15,
nr_queued = 0,
Example of md_sync thread stuck waiting on raise_barrier() and other
requests stuck in wait_barrier():
md1_resync
[<0>] raise_barrier+0xce/0x1c0
[<0>] raid10_sync_request+0x1ca/0x1ed0
[<0>] md_do_sync+0x779/0x1110
[<0>] md_thread+0x90/0x160
[<0>] kthread+0xbe/0xf0
[<0>] ret_from_fork+0x34/0x50
[<0>] ret_from_fork_asm+0x1a/0x30
kworker/u1040:2+flush-253:4
[<0>] wait_barrier+0x1de/0x220
[<0>] regular_request_wait+0x30/0x180
[<0>] raid10_make_request+0x261/0x1000
[<0>] md_handle_request+0x13b/0x230
[<0>] __submit_bio+0x107/0x1f0
[<0>] submit_bio_noacct_nocheck+0x16f/0x390
[<0>] ext4_io_submit+0x24/0x40
[<0>] ext4_do_writepages+0x254/0xc80
[<0>] ext4_writepages+0x84/0x120
[<0>] do_writepages+0x7a/0x260
[<0>] __writeback_single_inode+0x3d/0x300
[<0>] writeback_sb_inodes+0x1dd/0x470
[<0>] __writeback_inodes_wb+0x4c/0xe0
[<0>] wb_writeback+0x18b/0x2d0
[<0>] wb_workfn+0x2a1/0x400
[<0>] process_one_work+0x149/0x330
[<0>] worker_thread+0x2d2/0x410
[<0>] kthread+0xbe/0xf0
[<0>] ret_from_fork+0x34/0x50
[<0>] ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: authencesn - reject short ahash digests during instance creation
authencesn requires either a zero authsize or an authsize of at least
4 bytes because the ESN encrypt/decrypt paths always move 4 bytes of
high-order sequence number data at the end of the authenticated data.
While crypto_authenc_esn_setauthsize() already rejects explicit
non-zero authsizes in the range 1..3, crypto_authenc_esn_create()
still copied auth->digestsize into inst->alg.maxauthsize without
validating it. The AEAD core then initialized the tfm's default
authsize from that value.
As a result, selecting an ahash with digest size 1..3, such as
cbcmac(cipher_null), exposed authencesn instances whose default
authsize was invalid even though setauthsize() would have rejected the
same value. AF_ALG could then trigger the ESN tail handling with a
too-short tag and hit an out-of-bounds access.
Reject authencesn instances whose ahash digest size is in the invalid
non-zero range 1..3 so that no tfm can inherit an unsupported default
authsize. |
| In the Linux kernel, the following vulnerability has been resolved:
dm mirror: fix integer overflow in create_dirty_log()
The argument count calculation in create_dirty_log() performs
`*args_used = 2 + param_count` before validating against argc. When a
user provides a param_count close to UINT_MAX via the device mapper
table string, this unsigned addition wraps around to a small value,
causing the subsequent `argc < *args_used` check to be bypassed.
The overflowed param_count is then passed as argc to dm_dirty_log_create(),
where it can cause out-of-bounds reads on the argv array.
Fix by comparing param_count against argc - 2 before performing the
addition, following the same pattern used by parse_features() in the
same file. Since argc >= 2 is already guaranteed, the subtraction is
safe. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt()
ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read
when the queue reader or writer index from hardware exceeds
REMOTE_QUEUE_SIZE (60).
A compromised service processor can trigger this by writing an
out-of-range value to the reader or writer MMIO register before
asserting an interrupt. Since writer is re-read from hardware on
every loop iteration, it can also be set to an out-of-range value
after the loop has already started.
The root cause is that get_queue_reader() and get_queue_writer() return
raw readl() values that are passed directly into get_queue_entry(),
which computes:
queue_begin + reader * sizeof(struct remote_input)
with no bounds check. This unchecked MMIO address is then passed to
memcpy_fromio(), reading 8 bytes from unintended device registers.
For sufficiently large values the address falls outside the PCI BAR
mapping entirely, triggering a machine check exception.
Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of
the loop body, before any call to get_queue_entry(). On an out-of-range
value, reset the reader register to 0 via set_queue_reader() before
breaking, so that normal queue operation can resume if the corrupted
hardware state is transient. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: arp_tables: fix IEEE1394 ARP payload parsing
Weiming Shi says:
"arp_packet_match() unconditionally parses the ARP payload assuming two
hardware addresses are present (source and target). However,
IPv4-over-IEEE1394 ARP (RFC 2734) omits the target hardware address
field, and arp_hdr_len() already accounts for this by returning a
shorter length for ARPHRD_IEEE1394 devices.
As a result, on IEEE1394 interfaces arp_packet_match() advances past a
nonexistent target hardware address and reads the wrong bytes for both
the target device address comparison and the target IP address. This
causes arptables rules to match against garbage data, leading to
incorrect filtering decisions: packets that should be accepted may be
dropped and vice versa.
The ARP stack in net/ipv4/arp.c (arp_create and arp_process) already
handles this correctly by skipping the target hardware address for
ARPHRD_IEEE1394. Apply the same pattern to arp_packet_match()."
Mangle the original patch to always return 0 (no match) in case user
matches on the target hardware address which is never present in
IEEE1394.
Note that this returns 0 (no match) for either normal and inverse match
because matching in the target hardware address in ARPHRD_IEEE1394 has
never been supported by arptables. This is intentional, matching on the
target hardware address should never evaluate true for ARPHRD_IEEE1394.
Moreover, adjust arpt_mangle to drop the packet too as AI suggests:
In arpt_mangle, the logic assumes a standard ARP layout. Because
IEEE1394 (FireWire) omits the target hardware address, the linear
pointer arithmetic miscalculates the offset for the target IP address.
This causes mangling operations to write to the wrong location, leading
to packet corruption. To ensure safety, this patch drops packets
(NF_DROP) when mangling is requested for these fields on IEEE1394
devices, as the current implementation cannot correctly map the FireWire
ARP payload.
This omits both mangling target hardware and IP address. Even if IP
address mangling should be possible in IEEE1394, this would require
to adjust arpt_mangle offset calculation, which has never been
supported.
Based on patch from Weiming Shi <bestswngs@gmail.com>. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: cap upcall PID array size and pre-size vport replies
The vport netlink reply helpers allocate a fixed-size skb with
nlmsg_new(NLMSG_DEFAULT_SIZE, ...) but serialize the full upcall PID
array via ovs_vport_get_upcall_portids(). Since
ovs_vport_set_upcall_portids() accepts any non-zero multiple of
sizeof(u32) with no upper bound, a CAP_NET_ADMIN user can install a PID
array large enough to overflow the reply buffer, causing nla_put() to
fail with -EMSGSIZE and hitting BUG_ON(err < 0). On systems with
unprivileged user namespaces enabled (e.g., Ubuntu default), this is
reachable via unshare -Urn since OVS vport mutation operations use
GENL_UNS_ADMIN_PERM.
kernel BUG at net/openvswitch/datapath.c:2414!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 1 UID: 0 PID: 65 Comm: poc Not tainted 7.0.0-rc7-00195-geb216e422044 #1
RIP: 0010:ovs_vport_cmd_set+0x34c/0x400
Call Trace:
<TASK>
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1116)
genl_rcv_msg (net/netlink/genetlink.c:1194)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
genl_rcv (net/netlink/genetlink.c:1219)
netlink_unicast (net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Kernel panic - not syncing: Fatal exception
Reject attempts to set more PIDs than nr_cpu_ids in
ovs_vport_set_upcall_portids(), and pre-compute the worst-case reply
size in ovs_vport_cmd_msg_size() based on that bound, similar to the
existing ovs_dp_cmd_msg_size(). nr_cpu_ids matches the cap already
used by the per-CPU dispatch configuration on the datapath side
(ovs_dp_cmd_fill_info() serialises at most nr_cpu_ids PIDs), so the
two sides stay consistent. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: reject negative CO-RE accessor indices in bpf_core_parse_spec()
CO-RE accessor strings are colon-separated indices that describe a path
from a root BTF type to a target field, e.g. "0:1:2" walks through
nested struct members. bpf_core_parse_spec() parses each component with
sscanf("%d"), so negative values like -1 are silently accepted. The
subsequent bounds checks (access_idx >= btf_vlen(t)) only guard the
upper bound and always pass for negative values because C integer
promotion converts the __u16 btf_vlen result to int, making the
comparison (int)(-1) >= (int)(N) false for any positive N.
When -1 reaches btf_member_bit_offset() it gets cast to u32 0xffffffff,
producing an out-of-bounds read far past the members array. A crafted
BPF program with a negative CO-RE accessor on any struct that exists in
vmlinux BTF (e.g. task_struct) crashes the kernel deterministically
during BPF_PROG_LOAD on any system with CONFIG_DEBUG_INFO_BTF=y
(default on major distributions). The bug is reachable with CAP_BPF:
BUG: unable to handle page fault for address: ffffed11818b6626
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 85 Comm: poc Not tainted 7.0.0-rc6 #18 PREEMPT(full)
RIP: 0010:bpf_core_parse_spec (tools/lib/bpf/relo_core.c:354)
RAX: 00000000ffffffff
Call Trace:
<TASK>
bpf_core_calc_relo_insn (tools/lib/bpf/relo_core.c:1321)
bpf_core_apply (kernel/bpf/btf.c:9507)
check_core_relo (kernel/bpf/verifier.c:19475)
bpf_check (kernel/bpf/verifier.c:26031)
bpf_prog_load (kernel/bpf/syscall.c:3089)
__sys_bpf (kernel/bpf/syscall.c:6228)
</TASK>
CO-RE accessor indices are inherently non-negative (struct member index,
array element index, or enumerator index), so reject them immediately
after parsing. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix end-of-list detection in cgroup_storage_get_next_key()
list_next_entry() never returns NULL -- when the current element is the
last entry it wraps to the list head via container_of(). The subsequent
NULL check is therefore dead code and get_next_key() never returns
-ENOENT for the last element, instead reading storage->key from a bogus
pointer that aliases internal map fields and copying the result to
userspace.
Replace it with list_entry_is_head() so the function correctly returns
-ENOENT when there are no more entries. |
| In the Linux kernel, the following vulnerability has been resolved:
lib/crypto: mpi: Fix integer underflow in mpi_read_raw_from_sgl()
Yiming reports an integer underflow in mpi_read_raw_from_sgl() when
subtracting "lzeros" from the unsigned "nbytes".
For this to happen, the scatterlist "sgl" needs to occupy more bytes
than the "nbytes" parameter and the first "nbytes + 1" bytes of the
scatterlist must be zero. Under these conditions, the while loop
iterating over the scatterlist will count more zeroes than "nbytes",
subtract the number of zeroes from "nbytes" and cause the underflow.
When commit 2d4d1eea540b ("lib/mpi: Add mpi sgl helpers") originally
introduced the bug, it couldn't be triggered because all callers of
mpi_read_raw_from_sgl() passed a scatterlist whose length was equal to
"nbytes".
However since commit 63ba4d67594a ("KEYS: asymmetric: Use new crypto
interface without scatterlists"), the underflow can now actually be
triggered. When invoking a KEYCTL_PKEY_ENCRYPT system call with a
larger "out_len" than "in_len" and filling the "in" buffer with zeroes,
crypto_akcipher_sync_prep() will create an all-zero scatterlist used for
both the "src" and "dst" member of struct akcipher_request and thereby
fulfil the conditions to trigger the bug:
sys_keyctl()
keyctl_pkey_e_d_s()
asymmetric_key_eds_op()
software_key_eds_op()
crypto_akcipher_sync_encrypt()
crypto_akcipher_sync_prep()
crypto_akcipher_encrypt()
rsa_enc()
mpi_read_raw_from_sgl()
To the user this will be visible as a DoS as the kernel spins forever,
causing soft lockup splats as a side effect.
Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: Drop large packets with UDP encap
syzbot reported a WARN on my patch series [1]. The actual issue is an
overflow of 16-bit UDP length field, and it exists in the upstream code.
My series added a debug WARN with an overflow check that exposed the
issue, that's why syzbot tripped on my patches, rather than on upstream
code.
syzbot's repro:
r0 = socket$pppl2tp(0x18, 0x1, 0x1)
r1 = socket$inet6_udp(0xa, 0x2, 0x0)
connect$inet6(r1, &(0x7f00000000c0)={0xa, 0x0, 0x0, @loopback, 0xfffffffc}, 0x1c)
connect$pppl2tp(r0, &(0x7f0000000240)=@pppol2tpin6={0x18, 0x1, {0x0, r1, 0x4, 0x0, 0x0, 0x0, {0xa, 0x4e22, 0xffff, @ipv4={'\x00', '\xff\xff', @empty}}}}, 0x32)
writev(r0, &(0x7f0000000080)=[{&(0x7f0000000000)="ee", 0x34000}], 0x1)
It basically sends an oversized (0x34000 bytes) PPPoL2TP packet with UDP
encapsulation, and l2tp_xmit_core doesn't check for overflows when it
assigns the UDP length field. The value gets trimmed to 16 bites.
Add an overflow check that drops oversized packets and avoids sending
packets with trimmed UDP length to the wire.
syzbot's stack trace (with my patch applied):
len >= 65536u
WARNING: ./include/linux/udp.h:38 at udp_set_len_short include/linux/udp.h:38 [inline], CPU#1: syz.0.17/5957
WARNING: ./include/linux/udp.h:38 at l2tp_xmit_core net/l2tp/l2tp_core.c:1293 [inline], CPU#1: syz.0.17/5957
WARNING: ./include/linux/udp.h:38 at l2tp_xmit_skb+0x1204/0x18d0 net/l2tp/l2tp_core.c:1327, CPU#1: syz.0.17/5957
Modules linked in:
CPU: 1 UID: 0 PID: 5957 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
RIP: 0010:udp_set_len_short include/linux/udp.h:38 [inline]
RIP: 0010:l2tp_xmit_core net/l2tp/l2tp_core.c:1293 [inline]
RIP: 0010:l2tp_xmit_skb+0x1204/0x18d0 net/l2tp/l2tp_core.c:1327
Code: 0f 0b 90 e9 21 f9 ff ff e8 e9 05 ec f6 90 0f 0b 90 e9 8d f9 ff ff e8 db 05 ec f6 90 0f 0b 90 e9 cc f9 ff ff e8 cd 05 ec f6 90 <0f> 0b 90 e9 de fa ff ff 44 89 f1 80 e1 07 80 c1 03 38 c1 0f 8c 4f
RSP: 0018:ffffc90003d67878 EFLAGS: 00010293
RAX: ffffffff8ad985e3 RBX: ffff8881a6400090 RCX: ffff8881697f0000
RDX: 0000000000000000 RSI: 0000000000034010 RDI: 000000000000ffff
RBP: dffffc0000000000 R08: 0000000000000003 R09: 0000000000000004
R10: dffffc0000000000 R11: fffff520007acf00 R12: ffff8881baf20900
R13: 0000000000034010 R14: ffff8881a640008e R15: ffff8881760f7000
FS: 000055557e81f500(0000) GS:ffff8882a9467000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000200000033000 CR3: 00000001612f4000 CR4: 00000000000006f0
Call Trace:
<TASK>
pppol2tp_sendmsg+0x40a/0x5f0 net/l2tp/l2tp_ppp.c:302
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
sock_write_iter+0x503/0x550 net/socket.c:1195
do_iter_readv_writev+0x619/0x8c0 fs/read_write.c:-1
vfs_writev+0x33c/0x990 fs/read_write.c:1059
do_writev+0x154/0x2e0 fs/read_write.c:1105
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f636479c629
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffffd4241c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007f6364a15fa0 RCX: 00007f636479c629
RDX: 0000000000000001 RSI: 0000200000000080 RDI: 0000000000000003
RBP: 00007f6364832b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007f6364a15fac R14: 00007f6364a15fa0 R15: 00007f6364a15fa0
</TASK>
[1]: https://lore.kernel.org/all/20260226201600.222044-1-alice.kernel@fastmail.im/ |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: reject immediate NF_QUEUE verdict
nft_queue is always used from userspace nftables to deliver the NF_QUEUE
verdict. Immediately emitting an NF_QUEUE verdict is never used by the
userspace nft tools, so reject immediate NF_QUEUE verdicts.
The arp family does not provide queue support, but such an immediate
verdict is still reachable. Globally reject NF_QUEUE immediate verdicts
to address this issue. |
| Libgcrypt before 1.12.2 sometimes allows a heap-based buffer overflow and denial of service via crafted ECDH ciphertext to gcry_pk_decrypt. |
| A template injection vulnerability was discovered in the Dashboards functionality due to improper validation of an input parameter. An authenticated user with the required privileges can define a dashboard containing a malicious payload, or a victim can be socially engineered into importing a malicious dashboard. When the victim views or imports the dashboard, the payload executes in their browser context, allowing the attacker to modify application data or disrupt application availability. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-adc161s626: use DMA-safe memory for spi_read()
Add a DMA-safe buffer and use it for spi_read() instead of a stack
memory. All SPI buffers must be DMA-safe.
Since we only need up to 3 bytes, we just use a u8[] instead of __be16
and __be32 and change the conversion functions appropriately. |
